无码人妻一区二区三区精品视频-边摸边吃奶做爽a片视频-无码免费视频-中文字幕在线免费-97超级碰碰碰碰精品-毛片一区二区三区

Your location:Home  >  Textile knowledge

Comprehensive analysis of common faults and troubleshooting methods of winder

Author: Date:2020-01-10

       The quality of the product is the result of the combined effect of many factors. Under different conditions, the degree of each factor's effect is different, so the main and secondary factors must be distinguished in the analysis. Now let's talk about the common troubles of the winder and the troubleshooting methods.


Bobbin do not turn


       At the time of normal winding, the bobbin unwinding is completed, the middle yarn detecting device detects and sends a signal, and drives the transmission mechanism to move the spinning insert seat to the empty tube conveyor belt and kick the empty yarn tube into the conveyor belt. The stepping motor passes the transmission. The lever causes the ratchet to rotate one tooth, and the bobbin magazine rotates a certain angle to fill the full yarn into the insertion spindle holder, and then the insertion spindle holder moves back to the working position.


Because the ratchet part is blocked by velvet or filament winding, the ratchet cannot be driven by the pawl, so the failure of the yarn storehouse occurs. As long as the parts of the yarn storage are removed, the lint or loops can be removed to return to normal. When using compressed air for cleaning every week, as long as the cleaning is in place, this failure can be prevented.


The bobbin is frequently withdrawn by the bobbin changing device


       Under the condition that the tube yarns are not uniformly dried out, the fault is caused by the soiling and failure of the surface of the middle yarn detecting device, as long as the detection surface is wiped clean. Regularly cleaning the detection part of the yarn detection device is the best way to prevent this failure.


Scissors are not sharp


       If the scissors are not sharp enough to cut the yarn, the yarn sucked by the small suction nozzle will be folded into double yarns at the fixed suction nozzle, so that it will be cut when passing through the yarn clearer. This is repeated several times, resulting in abnormal production. And increase energy consumption. Remove the scissors part for maintenance and replace with a new pair of scissors. Do not discard the sharp scissors. They can be sent to a mechanical maintenance and processing workshop (machine repair workshop for short) to be sharpened and continued to be used.


Tension device malfunctions


       The tension device provides proper tension to the yarn through the tension disc. The tension disc is divided into a pressure disc and a stationary disc. The stationary disk is fixed, and the pressure disk can move and swing axially. When the reel is wound in the pressure plate, its movement is blocked, which causes the tension to be unstable, the winding density to be uneven, and head breakage often occurs.


When repairing, dismantle it according to the operating specifications and remove the debris such as loops.


Large nozzle leaks air


       When the large suction nozzle is at the zero position, use a yarn to place it next to the large suction nozzle. If the yarn is sucked into the large suction nozzle, it means that the large suction nozzle leaks air. Air leakage from the large nozzle will not only cause waste of energy, but also make other parts with insufficient air pressure. Whether the large nozzle sucks air is determined by the large nozzle energy-saving trap on the damper. When the trap is opened, the large nozzle sucks air, otherwise it doesn't suck air. The large nozzle leakage is caused by the flaps being loosely closed by the cotton wool dust. Therefore, when the maintenance is performed, the damper should be removed, the cotton wool dust should be cleaned, and the drive to open the flap. Cylinder piston, apply sealing grease to achieve sealing and lubrication. After the air damper is installed, use the yarn again to check whether there is no air leakage, and make sure to repair one.


       The large nozzle leakage is caused by the flaps being loosely closed by the cotton wool dust. Therefore, when the maintenance is performed, the damper should be removed, the cotton wool dust should be cleaned, and the drive to open the flap. Cylinder piston, apply sealing grease to achieve sealing and lubrication. After the air damper is installed, use the yarn again to check whether there is no air leakage, and make sure to repair one.


Unsuccessful splicing or splicing failure


       Splicing failure or splicing failure is caused by three reasons. First, improper process design and unreasonable splicing parameters. The second is that the position of the yarn lever is incorrect, and the yarn cannot be transferred into the splicer. Third, the splicer is inflexible due to lack of oil, the seal is leaking, the splicing cover is damaged or it fails to pop up.


       The first reason is that the splicing parameters can be changed due to human reasons, and then a splicing test is performed to check whether the splicing parameters are reasonable.


       Cause two, you can loosen the fixing screw on the yarn lever and correct the position.


       The third reason is often the cause, and it is also the focus of maintenance work. Maintenance can be carried out according to specific conditions, and if necessary, lubricate the moving parts.


Yarn clearer failure


       The yarn clearer is another key component that affects the quality of the winder. Automatic winders usually use electronic yarn clearers, which are divided into photoelectric and capacitive types. Now take TK830 capacitive yarn clearer produced by LOEPFE company as an example to analyze it.


       If there is a mechanical wave in the bobbin, the yarn clearer will cut after a few revolutions of the grooved drum. At this time, changing the bobbin can resume normal production. When the yarn clearer fails, frequent shearing action occurs in a short time, so that production cannot be continued. The troubleshooting method is to reset the yarn clearer, and the reset times should be more than two times to ensure that the reset is accurate. If the reset is invalid, it can be concluded that the internal components of the yarn clearer are damaged and can be handed over to an electrician.


Sleeve grip arm size collet is not flexible


       The big and small chucks on the bobbin holding arm are high-speed parts, and its rotation speed is close to the speed of the grooved bobbin, so the bearing wear failure often occurs. After the fault occurs, the package is difficult to rotate, the yarns are not evenly arranged, and an alarm will appear. As long as the bearing in the chuck is taken out and replaced with a new one, normal production can be resumed.


Contact person: Hu bamboo shoots
Fax: 86-511-86282666
Mobile phone: (0) 13511683888
Email: Sales@hengda-textile.com
Address: Hengtang Town, Danyang City, Jiangsu, China

? Copyright Danyang Hengda Textile Co., Ltd. record number:蘇ICP備16016098號 Technical Support:ERUN

主站蜘蛛池模板: 91视频网站免费在线观看 | 91精品高清在线观看免费 | 国产福利小视频 | 波多野在线 | 亚洲欧洲一区二区三区 | 在线免费观看国 | 日b大全在线观看免费 | 国产一区在线午夜福利影片观看 | 色伊人 | 日韩一级在线精品国产 | 2025自拍偷拍 | 中文字幕日本αv一区二区 国产日韩欧美 | 日韩乱伦中文字幕 | 中文字幕在线亚洲日韩6页 国产在线视频国产永久 | 九色精品 | 真实国产精品视频400部 | 91免费国产自产地址入 | 午夜国产1024| 日韩乱码视频 | 成人二区 | 91视频播放| 日韩在线观看91精品免费 | 中文字字幕乱码高清二本道资源站 | 日韩成人一区二区三区在线观看 | 五月天蜜桃综合网 | 国产浮力第一页 | 天天影视网色香欲综合网 | 日韩性爱免费网站 | 91传媒制片厂制作网 | 日韩高清成人a∨一区二区 资源稳定站在线观看 | 亚洲一在线 | 91抖阴短视频无限观看版app下载 | 丰满岳乱妇在线观看中字 | 国产精品亚洲 | 91绿帽论坛 | 韩国一区二区三区中文字幕 | 色老头在线一区二区三区 | 亚洲高清一区二区三区不卡 | 免费特级欧美片 | 亚洲图片小说三级页面 | 国产25页 |